Corporation

Datasheet
The Scorpion L-SBS (Small Blasting System) is a compact and rugged light-weight Solid-State Electronic Capacitor Discharge Blasting Machine meant for either Electric Initiation or Non-Electric Shock Tube Initiation. For electric circuits, the unit incorporates a Circuit Continuity Indicator (CCI) allowing the operator to verify a complete circuit has been attached to the Output Binding Posts prior to initiation. The L-SBS is completely sealed making it waterproof and impervious to dust, dirt, sand, and debris. One 9V battery provides hundreds of Charge/Fire cycles, and loads smoothly through the side of the unit into a waterproof compartment secured in place by an easy-on/off battery cap that requires no tools. Electric Initiation: The Scorpion L-SBS features EIT’s specially developed Heavy-Duty Push Down Binding Posts for quick and secure lead line attachment, even when wearing gloves. The CCI uses a secure blasting-safe signal to detect a circuit is present and informs the operator with a green LED. When “Charge” is depressed the CCI is immediately disengaged. The CCI will only reengage when “Charge” is released and the redundant safety allows use of the indicator once again. The L-SBS incorporates 2 recessed covered pushbutton switches for Charge/Fire operations and is engineered for rapid charging. Non-Electric Initiation: The Scorpion L-SBS incorporates a separate 2.5kV high voltage circuit and capacitor, different from that of the Electric Initiator, to create a pulse that initiates non- electric shock tube. Using two separate initiation circuits protects the output of either system and insures dual reliability. The unit uses a guarded pushbutton switch located on the side of the unit to activate the Non-Electric system.
Datasheet
L‐SBS

Scorpion Solid‐State Electronic Blasting Machine & Non‐Electric Initiator

ELECTRIC INITIATION
FIRING ENERGY:225 VDC @ 4.0Joules
FIRING CAPABILITY:Electric Blasting Caps
FIRING CAPACITY:135 Ohms
circuits requiring minimum 1.5A @ 20mJ/Ohm of resistance
FIRE CIRCUIT:Locked out unless full charge is available
ARMED INDICATOR:High visibility green LED
LEAD LINE CONTINUITY DETECTION
DETECTION:Automatic & immediate indication of circuit
TEST SIGNAL:<0.18mA(0.00018A), Fuse Protected
INDICATION:Separate high visibility green LED
NON -ELECTRIC INITIATION
FIRING ENERGY:2,500 VDC @ 0.5Joules
FIRING CAPACITY:1 Non -Electric Shock Tube Line
CONNECTION:Replaceable Shock Tube Connector (STC )
TYPE:EIT STC -E (Electrode In Tube )
SAFETY
ELECTRIC OUTPUT:Binding Posts shunted internally
ELECTRIC ABORT:Safe internal discharge when ‘Charge’ switch is released before ‘Fire’
ELECTRIC FIRING:Requires sequenced 2 switch operation
CONTINUITY:Indicator immediately disengages during Charge/Fire operation
MECHANICAL
DIMENSION:3″wide x 2″thick x 6″high (7.6cmx 5cmx 15.2cm)
WEIGHT:18 oz w /battery (510g)
CASE MATERIAL:HD Urethane
HARDWARE:Brass, Nylon, Rubber
INGRESS:IP68 (3m)
OPERATING TEMP:Tested -20°F -140°F (-29°C -60°C )
STORAGE TEMP:Tested -45°F -180°F (-42°C -82°C )
COLORS:Black, Yellow, Tan, OD Green
POWER SOURCE
BATTERY:Replaceable 9V (HD alkaline recommended )
LIFE:~300+ Charge/Fire Cycles typical
FEATURES
CONNECTION:EIT’s quick-connect HD Output Binding Posts
SWITCHES:Recessed & Guarded with rugged waterproof boots
BATTERY:Battery loads smoothly through side of unit and is secured in place by easy-on/off battery cap
WARRANTY:Lifetime warranty against manufacturing defects
Superior Field Reliability

Scorpion devices are built with the highest quality electronics and components so you can count on them to work in even the most unforgiving environments. Engineered for long life, Scorpion devices continue to provide reliable performance for decades in the field where other manufacturers break down after only months.

Quick and easy battery replacement in 1 step

Scorpion units are designed with a waterproof battery compartment for quick and easy replacement. No need to remove screws and, as with competitors machines, expose the wiring and internal components just to change the batteries. EIT developed the one step on and off compartment cover to let you replace a battery anywhere- no tools required.